Regrind
Regrind is in-plant thermoplastic scrap, such as sprues, runners and rejected parts, ground for return to the process. The term describes the material's origin and form; it does not establish suitability for a particular part.

On this page · 5 sections
How does Regrind apply to your shop floor?
Pick your industry and scale — Ask V5 rewrites the definition in your context, gives a worked example, and shows what V5 does on day one.
01How regrind differs from other feedstocks
In plastics and resin processing, feedstock labels describe different material histories. Here, regrind means internal scrap recovery, rather than every form of recycled resin.
- Virgin resin is new resin supplied for processing, rather than resin recovered from scrap or used products.
- Purchased reprocessed material has been recovered and processed outside the plant. Its provenance and processing history depend on information from that supply chain, not only the receiving plant's production records.
- Post-consumer recycled material comes from products after consumer use. That history differs from scrap generated during manufacturing.
02Manufacturer guidance: material family and part both matter
The following percentages are named-family manufacturer processing recommendations, not universal limits, standards or legal limits. They do not establish an acceptable percentage for every thermoplastic or every part.
DuPont Zytel and Minlon
The DuPont Zytel/Minlon molding guide, section 10, recommends using only regrind from optimally processed original material. It recommends using rework as generated and restricting the level to a maximum of 50%, or preferably 25%, blended with virgin material.
DuPont states that the actual amount must be determined for each part by testing. Acceptability depends on that molded part's operational and performance requirements. For reinforced Zytel, the guide warns that mechanical-property losses could become significant depending on the regrind proportion. It also notes that regrind quality is more likely than regrind percentage to affect final part properties.
DuPont recommends protecting regrind from moisture, keeping it in sealed moisture-proof containers, and drying it before processing to avoid moisture-related degradation. Its handling guidance also calls for contamination-free material, minimal handling of sprues and runners with lint-free gloves, uniform particles approximately the size of fresh pellets or granules, and removal and avoidance of fines.
DuPont advises against using discolored or splayed molded parts and runners, or material previously degraded by high moisture or excessive barrel residence. For molded parts made brittle by excessive moisture or prolonged barrel residence, it states that they must be discarded and not reused.
Covestro TPU
The Covestro TPU injection molding guide, section 3.3, describes recycling clean, sorted scrap from processing its TPU after appropriate treatment and drying. It recommends a recycled-material proportion of not more than 30%.
03Plant controls: separate identity, condition and qualified use
A plant may use the following record structure to make regrind decisions traceable. These are suggested plant controls, not a manufacturer-prescribed record format. The questions are distinct: known identity does not prove cleanliness, and clean material does not establish qualified use.
| Control | Question it answers | What the plant may record |
|---|---|---|
| Provenance | Which resin, grade and lot is this, and which process generated it? | Resin identification, grade, color, original lot, generating machine and run, scrap type, rejection reason, and regrind container identifier. |
| Contamination | Does the material contain foreign matter, lint, fines or mixed grades? | Inspection findings, grinder cleanout status, fines removal, suspected mixing, treatment performed, and the resulting material disposition. |
| Segregation | Has the material remained separate by grade, color and lot, sealed and protected from moisture? | Container labels, storage location, closure condition, transfers, moisture exposure and any loss of segregation. |
| Qualified use | For which part and proportion has use been accepted after testing against operational and performance requirements? | Part and revision, resin grade, accepted ratio and its calculation basis, qualification scope, test results and approving personnel. |
| Material history | How many heat histories has the material experienced, and what processing problems occurred? | Known processing passes, previous regrind returns, residence and moisture problems, drying history, discoloration, splay, brittleness, and hold or discard decisions. |
When regrind returns through the process again, carry its earlier history forward rather than treating the next container as fresh scrap. If the number of heat histories is unknown, record that uncertainty; creating a new container record does not resolve it.
04A controlled return-to-process flow
This is an example plant workflow. Establish the part qualification before routine production; the final checkpoint below is the planned production test and human release, not a substitute for qualification. Material that fails a checkpoint leaves the return stream for a documented disposition.
- Scrap generatedCapture the resin, grade, lot, originating run and reason the material became scrap.
- Segregated and protectedAssign a labeled container and preserve separation and moisture protection through storage and transfer.
- Inspected and groundEvaluate material against plant acceptance criteria and document inspection, grinding and disposition.
- DriedApply the drying conditions selected for the grade and record completion.
- Blended at qualified ratioWeigh and record the feed components against the approved part-specific blend instruction.
- Part tested and released by peoplePerform planned part checks. Responsible personnel review the results and decide release.
05Worked cases: calculate the blend, then decide its disposition
These fictional cases illustrate decisions, not validated processing instructions. For the calculations, assume the stated masses are the only feed components, both enter the blend without loss, and percentage means regrind mass divided by total feed mass. Arithmetic alone does not qualify a ratio for a part.
| Case | Given | Decision | Evidence or records |
|---|---|---|---|
| RG-A | A molder proposes 2 kg regrind with 3 kg virgin for a reinforced Zytel part because the proportion is below 50%. The part has not been tested. | 2 / (2 + 3) = 40% regrind by mass. Do not approve the proposal from the family percentage alone; perform the part testing described above. | Part-specific test results against operational and performance requirements, with a documented accepted ratio. |
| RG-B | Runners from a shift with a moisture alarm are discolored and splayed. | Discard; do not grind for reuse. | Identify the affected run and containers; record the alarm, observations and discard disposition. |
| RG-C | Scrap from different Covestro TPU grades was collected in one open bin. | This is not a clean, sorted stream. Hold separately for identification and sorting; discard if reliable separation cannot be established. Do not feed it as collected. | Grade identity, reliable sorting, cleanliness, exposure history, appropriate treatment and drying. |
| RG-D | A plant blends 1 kg of dried, same-grade, uniformly sized regrind with 3 kg of virgin pellets. The part is already qualified at that ratio. | 1 / (1 + 3) = 25% regrind by mass. This is within the assumed qualification; document the blend and follow the planned production checks. | Resin, grade and lot provenance; generating run; material history; drying record; actual blend masses; qualification reference; human release decision. |
| RG-E | A customer asks whether in-plant origin alone establishes acceptability for a particular end use. | Outside this definition's scope. Refer the intended application for a separate suitability assessment. | An application-specific assessment rather than an inference from the material's in-plant origin. |
Frequently asked questions
Q.How should the ratio be written on a blend record?+
State the calculation basis explicitly. For a mass-based blend, record each component's mass and the regrind fraction of total feed, rather than an unexplained percentage. This lets another person reconstruct the calculation and compare it with the qualification record.
Q.Can a drying record replace the material-history record?+
No. It documents the drying operation, not the full processing history. Link it to the material-history and disposition records described above rather than using it to close unrelated material questions.
Q.What should happen when the resin grade or intended part changes?+
Treat the change as a review point. Compare the proposed material and part with the scope of the qualification record before scheduling production, and document whether further testing is needed.
Primary sources
Want to see how Regrind could fit into your own records and workflows? Explore the related V5 pages or talk to our team about what applies to your operation.
