Safety Data Sheet (SDS): How to Read and Match a US OSHA SDS
An SDS is useful only when it describes the chemical actually in hand and the reader can find the relevant information. This guide covers US OSHA workplace hazardous chemicals, with practical checks for identity, content and access.
Read the full summary
Other jurisdictions are outside scope and must be checked separately.

On this page · 7 sections
- 1What a safety data sheet is under US OSHA
- 2Match the SDS to the chemical in hand
- 3Find the relevant SDS section
- 4Recognize missing information without guessing
- 5Check employee access separately from document content
- 6A practical reading and matching path
- 7Worked cases: identify the defect and the next step
01What a safety data sheet is under US OSHA
Under US OSHA's 29 CFR 1910.1200(c), a safety data sheet, or SDS, is written or printed material concerning a hazardous chemical, prepared in accordance with paragraph (g). It is a chemical-information document: the reading task begins by establishing which product it describes, then locating the information relevant to the question.
For US hazardous chemicals covered by HazCom, (g)(1) requires chemical manufacturers and importers to obtain or develop an SDS for each hazardous chemical they produce or import, and employers to have an SDS in the workplace for each hazardous chemical they use. These are distinct responsibilities: preparing or obtaining the document is not the same task as making it usable at the workplace.
US OSHA's scope provision, (b)(2), addresses chemicals known to be present in the workplace in a manner that may expose employees during normal use or a foreseeable emergency. Check the full scope provision when deciding whether a particular product or activity falls within the standard.
For US workplace hazardous chemicals, (b)(1) places SDSs alongside a hazard communication program, labels and other warnings, information, and training. An SDS therefore belongs within a wider communication system, rather than standing alone. See the HazCom classification and labeling readiness guide for that broader context.
02Match the SDS to the chemical in hand
For US hazardous chemicals, OSHA's product identifier definition in (c) describes the name or number used on a label or in the SDS. Under that US OSHA definition, the identifier must permit cross-references among the written hazard communication program's chemical list, the label and the SDS.
For US hazardous-chemical SDSs, Appendix D, Table D.1, Section 1 specifies the product identifier used on the label, other means of identification, and recommended use and restrictions on use. The same US OSHA section specifies the name, US address and US telephone number of the chemical manufacturer, importer or other responsible party, plus an emergency phone number.
Suggested receiving practice—not an additional OSHA receiving procedure: compare the physical container label with Section 1 before relying on the document's technical content. A familiar brand, supplier or ingredient name is a starting point, not a reason to overlook a different product identifier.
- Compare the complete product name or number, including any part, grade or formulation distinction shown in the identifier.
- Check the corresponding chemical-list entry. Record a discrepancy rather than silently treating different names as equivalent.
- Use the named manufacturer, importer or responsible party to direct a clarification request; a similar-looking container does not resolve an identity question.
- Ask for an SDS that demonstrably covers the labeled product when the match remains unresolved.
Practice: separate the document question from the material-disposition decision. Refer an unresolved identity issue to the site's responsible person. Any internal quarantine status follows the site's disposition procedure; this reading check does not itself authorize use or release of the material.
03Find the relevant SDS section
For US hazardous-chemical SDSs, (g)(2) requires English, permits employers to maintain additional language copies, and lists all sixteen numbered headings in order. The navigation summary below follows that list; Appendix D, Table D.1 specifies the content. This is a section map, not a substitute for the full content specification.
| Section | Heading | What to look for |
|---|---|---|
| 1 | Identification | The product identifier and responsible-party contact details; begin the product match here. |
| 2 | Hazard(s) identification | Chemical classification, signal word, hazard statements, symbols and precautionary statements. |
| 3 | Composition/information on ingredients | Chemical and ingredient identities, including CAS numbers or other unique identifiers. |
| 4 | First-aid measures | Measures organized by exposure route, important symptoms or effects, and indications for medical attention or special treatment. |
| 5 | Fire-fighting measures | Extinguishing media, hazards arising from the chemical, and special equipment or precautions for fire-fighters. |
| 6 | Accidental release measures | Personal precautions, protective equipment, emergency procedures, and containment and cleanup methods. |
| 7 | Handling and storage | Safe-handling precautions and storage conditions, including incompatibilities. |
| 8 | Exposure controls/personal protection | Available exposure limits for Section 3 ingredients or constituents, engineering controls and individual protection measures. |
| 9 | Physical and chemical properties | Properties including physical state, flash point and solubility. |
| 10 | Stability and reactivity | Reactivity, stability, hazardous reactions, conditions to avoid, incompatible materials and hazardous decomposition products. |
| 11 | Toxicological information | Health effects and the available data used to identify those effects. |
| 12 | Ecological information | Ecotoxicity, persistence and degradability. |
| 13 | Disposal considerations | Waste residues and disposal methods, including contaminated packaging. |
| 14 | Transport information | UN number, proper shipping name, transport hazard classes and packing group where applicable. |
| 15 | Regulatory information | Safety, health and environmental regulations specific to the product. |
| 16 | Other information, including date of preparation or last revision | The date of preparation of the SDS or the last change to it. |
For US hazardous-chemical SDSs, (g)(2) explicitly says the headings for Sections 12–15 must also be included in order for consistency with the GHS; its note says OSHA will not enforce information requirements in those sections because these areas are outside its jurisdiction. For these US OSHA SDSs, Appendix D's lead text says Sections 12–15 may be included but are not mandatory, and Table D.1 labels them non-mandatory. For a reading check, distinguish missing headings from missing information within those headings.
Practice: read related sections together without treating them as interchangeable. Hazard identification, exposure controls and toxicological information answer different questions. Read units and qualifiers as written, and send apparent contradictions to a competent reviewer rather than selecting whichever statement seems more convenient. This map does not prescribe handling, protective equipment or emergency actions for any particular chemical.
04Recognize missing information without guessing
For US hazardous-chemical SDSs, Appendix D requires the specified Table D.1 information under the indicated section numbers and headings for Sections 1–11 and 16. Under US OSHA Appendix D, each section must contain all specified information, but the information may appear in any order within that section. A different arrangement of subheadings is therefore not, by itself, evidence that content is missing.
For US hazardous-chemical SDSs, (g)(3) requires the chemical manufacturer, importer or employer preparing the SDS to mark a subheading when no relevant information is found, indicating that no applicable information was found. US OSHA's Appendix D likewise requires a clear indication that no applicable information is available.
Practice: treat an unexplained empty field as an unresolved information question, not as a chemical value. A blank does not establish that a property is irrelevant or that a hazard is absent. A clear statement that no applicable information was found communicates a limitation; it does not, on its own, establish that a particular workplace task is safe.
- Suggested reading check: locate the relevant content throughout the section before concluding that a differently arranged field is absent.
- Record the section, subheading and actual entry, including whether the field is empty or contains an explanation.
- Ask the preparer or supplier to clarify an unresolved entry; do not supply a guessed value or copy one from a different product.
- Have a responsible reviewer assess the answer and the corrected document, including whether any practical question remains unanswered.
05Check employee access separately from document content
For US workplace hazardous chemicals, (g)(8) requires employers to maintain copies of the required SDSs in the workplace and ensure they are readily accessible during each work shift to employees in their work areas. Under this US OSHA provision, electronic access and alternatives to paper copies are permitted only when they create no barriers to immediate employee access in each workplace.
For US hazardous-chemical workplaces where employees travel between geographical locations during a workshift, (g)(9) permits SDSs to be kept at the primary workplace facility, but requires the employer to ensure employees can immediately obtain the required information in an emergency.
For US workplace hazardous chemicals, (g)(10) permits SDSs in any form, including operating procedures, and permits grouping chemicals where addressing process hazards may be more appropriate than addressing individual chemicals. Under that US OSHA provision, the employer must still ensure the required information is provided for each hazardous chemical and is readily accessible during each work shift to employees in their work areas.
For US workplace hazardous chemicals, (g)(11) also requires SDSs to be made readily available upon request to designated representatives, the Assistant Secretary and the Director, in accordance with § 1910.1020(e).
Practice: check access from the employee's work area using the arrangements actually available on that shift. An office demonstration does not establish access when the office is closed or the usual contact is absent. Record an access barrier separately from a content defect so the appropriate person can resolve it. A corrected document and a usable access arrangement solve different problems.
06A practical reading and matching path
The following is a suggested human review sequence, not an OSHA-prescribed receiving checklist. It separates product identity, document content and employee access. A reviewer can return to an earlier step when a later finding raises a new question; reaching the end is not a material-release decision.
- MatchCompare the label, Section 1 and the chemical-list entry. Refer an unresolved identifier mismatch for clarification.
- Labeled product identifier
- SDS coverage
- NavigateUse the section map to locate the subject of the question.
- Relevant section
- Related information
- InspectDistinguish present information, an explicit limitation and an unexplained gap.
- Subheading
- Actual entry
- Test accessCheck the employee's real work-area and shift arrangements.
- Access route
- Observed barrier
- ResolveA responsible person reviews the clarification, revised SDS or restored access.
- Resolution
- Remaining questions
Practice: connect the reading checklist to the document being reviewed through document control. Record what was compared, the question raised and who assessed the response. Where a clarification may affect site instructions, refer it through the site's change control process for assessment rather than assuming that receiving a replacement SDS resolves every operational consequence.
07Worked cases: identify the defect and the next step
Assumptions: these are fictional US workplace cases involving hazardous chemicals covered by OSHA HazCom. Each case addresses the stated document or access issue, not a complete chemical risk assessment. No quantities, units or calculations are involved. The follow-up actions are suggested practice based on the distinctions above.
| Case | Observation | Decision and practical next step | What is needed to resolve it |
|---|---|---|---|
| SD-A | At a coatings plant, the drum label says FlexBond 220 Part B Hardener, but the filed SDS says FlexBond 220 Part A Resin. The chemical list contains separate entries for both parts. | Identifier mismatch. Obtain an SDS matching Part B Hardener; do not accept the Part A document merely because the product-family name matches. | An SDS covering the labeled Part B product and permitting the corresponding chemical-list cross-reference. |
| SD-B | The solvent blend SB-7 SDS has Sections 1–11 and 16, which appear complete, but no headings for Sections 12–15. | Request a revised SDS with the missing headings, applying the heading-versus-information distinction above. | A revised document with all sixteen numbered headings in order. |
| SD-C | The additive AX-3 SDS contains a flash-point subheading in Section 9, but the field is empty and has no explanation. | Request correction or clarification of the unmarked blank. Do not interpret it as a flash-point result. | The applicable entry, or a clear indication that no applicable information was found, for human review. |
| SD-D | An importer receives an SDS showing only an overseas company address and non-US telephone number in Section 1, with no US responsible-party contact details or emergency phone. | Request a revised Section 1 contact set. | The responsible party's name, US address and US telephone number, plus an emergency phone number. |
| SD-E | SDS files are on an office PC locked overnight. Night-shift mixing-area operators cannot open them until the supervisor arrives. | Fix the employee-access barrier. A supplier document revision does not address this problem. | A demonstrated arrangement giving night-shift employees immediate access to the electronic SDSs in their work area. |
Practice: close the stated discrepancy only after a person reviews the revised document or demonstrates restored access. Record any remaining question separately. Resolving one defect does not establish that the entire SDS or the workplace arrangements have been assessed.
Frequently asked questions
Q.What if the document is called an MSDS?+
The current US OSHA standard calls the hazardous-chemical document a safety data sheet in 1910.1200(g). Practice: assess the document's identity, content and accessibility using the checks above rather than deciding adequacy from its title alone.
Q.Can one SDS cover several mixtures?+
For US hazardous chemicals, (g)(4) permits a manufacturer, importer or employer to prepare one SDS for complex mixtures with similar hazards and contents: the ingredients are essentially the same, while specific composition varies. Practice: ask whether the particular mixture is covered; a shared product-family name alone does not establish those conditions.
Q.How is a trade-secret statement different from an unexplained blank?+
For US hazardous-chemical SDSs, Table D.1, Section 3 requires a statement when chemical identity and/or concentration is withheld as a trade secret in accordance with paragraph (i). Practice: recognize that statement as an explanation of withholding, not as a value you can infer or reconstruct.
Q.What should a supplier clarification request contain?+
Suggested practice: identify the product exactly as labeled, name the relevant section and subheading, attach the relevant label image or document page, and describe the discrepancy without proposing an unsupported chemical value. Ask for a matching or corrected SDS, then have a responsible person assess whether the response resolves the question.
Primary sources
- 29 CFR 1910.1200(b)(1)-(2) — eCFR 30 October 2026
- 29 CFR 1910.1200(c) "Product identifier" — eCFR 30 October 2026
- 29 CFR 1910.1200(c) "Safety data sheet" — eCFR 30 October 2026
- 29 CFR 1910.1200(g)(1)-(4) — eCFR 30 October 2026
- 29 CFR 1910.1200(g)(8)-(11) — eCFR 30 October 2026
- 29 CFR 1910.1200 Appendix D (lead text) — eCFR 30 October 2026
- 29 CFR 1910.1200 Appendix D, Table D.1 — OSHA.gov (as amended 8 Jan 2026), read 3 Nov 2026
Further reading
Explore this topic
MSDS / SDS sits inside this topic cluster in our glossary. Every neighbour is one click away.
SDS, OEL/OEB banding, ALARA and worker-exposure controls.
Want to see how MSDS / SDS could fit into your own records and workflows? Explore the related V5 pages or talk to our team about what applies to your operation.
