VOC Content (Architectural Coatings)
VOC content is the weight of volatile organic compounds per volume of an architectural coating, calculated under 40 CFR 59.406(a) and compared with its Table 1 category limit. US federal rule, eCFR version as of 29 October 2026.

On this page · 5 sections
- 1VOC Content (Architectural Coatings): Definition and Federal Scope
- 2Federal Rule: Category, Calculation Basis and Applicable Limit
- 3Federal Rule: Container Information (40 CFR 59.405(a))
- 4Federal Rule: Conditional Records and Initial Notification
- 5Fictional Practice Example: Label and Evidence Decision
01VOC Content (Architectural Coatings): Definition and Federal Scope
VOC content means the weight of volatile organic compounds per volume of coating, calculated under 59.406(a), as specified in 59.401. This definition addresses US federal 40 CFR 59 subpart D only, as published in the eCFR on 29 October 2026.
An architectural coating is recommended for field application to stationary structures and their appurtenances, portable buildings, pavements or curbs. The 59.401 definition excludes adhesives and coatings recommended by the manufacturer or importer solely for shop applications or solely for non-stationary structures, such as airplanes, ships, boats and railcars. The word “solely” matters: a shop-only recommendation is different from a coating also represented for covered field uses.
The subpart applies to manufacturers and importers of covered architectural coatings for US sale or distribution. Under 59.401, manufacturers include persons producing, packaging or repackaging those coatings; importers bring them into the United States for domestic sale or distribution. Both definitions contain specific repackaging exclusions.
Section 59.400 generally covers architectural coatings manufactured on or after September 13, 1999. For coatings registered under the Federal Insecticide, Fungicide, and Rodenticide Act, applicability begins with manufacture on or after March 13, 2000.
Section 59.400(c) excludes these coatings from the subpart:
- Coatings manufactured for architectural-coating markets outside the United States; they must not be sold or distributed within the United States as architectural coatings.
- Coatings manufactured before September 13, 1999.
- Coatings sold in nonrefillable aerosol containers.
- Coatings collected and redistributed at a paint exchange.
- Coatings sold in containers with a volume of one liter or less.
02Federal Rule: Category, Calculation Basis and Applicable Limit
Under 59.402(a), each manufacturer and importer must ensure that a covered coating's VOC content does not exceed its applicable Table 1 limit, except as provided in 59.403 and 59.404.
Unless otherwise specified, Table 1 limits are grams of VOC per liter of coating (g/L), thinned to the manufacturer's maximum recommendation, excluding volumes of water, exempt compounds and colorant added to tint bases. Section 59.406 requires tint-base content to be determined without colorant added after manufacture or import. Its paragraph (a)(1) identifies an exception for low solids stains and low solids wood preservatives. Compliance is determined in metric units; Table 1's lb/gal values are informational.
- Flat coatings, interior or exterior: 250 g/L.
- Nonflat coatings, interior or exterior: 380 g/L.
- Primers and undercoaters: 350 g/L.
Under 59.402(b), representations indicating more than one Table 1 category generally trigger the most restrictive VOC-content limit. This covers the container, attached labels or stickers, and sales, advertising or technical literature supplied by the manufacturer, importer or anyone acting on their behalf. Section 59.402(c) provides exceptions; the rule is therefore not an exception-free instruction to choose the lowest limit.
Table 1 also lists quick-dry primers, sealers and undercoaters as a separate subcategory under its Quick-dry coatings heading. That subcategory has its own definition in 59.401 and is addressed by 59.402(c)(13); an ordinary primer is not placed there by its name alone.
03Federal Rule: Container Information (40 CFR 59.405(a))
Manufacturers and importers must provide the following information on the container in which a covered coating is sold or distributed. The permitted location differs by item:
- Manufacture date or date code: on the label, lid or bottom of the container.
- Manufacturer's thinning recommendation: on the label or lid. This requirement does not apply to thinning with water. If thinning before use is unnecessary, the recommendation must specify application without thinning.
- VOC statement: on the label or lid, showing either the coating's VOC content or the Table 1 limit it is required to meet and actually meets. Either option may use grams of VOC per liter or pounds of VOC per gallon. The limit-labeling option is conditional, not permission to replace a higher actual content with a lower category limit.
04Federal Rule: Conditional Records and Initial Notification
Section 59.407 requires specified written or electronic records when a manufacturer or importer uses a particular route. It is not a universal recordkeeping checklist for every architectural coating:
- Recycled-coating calculation route under 59.406(a)(3): the records specified in 59.407(a).
- Exceedance-fee provisions under 59.403: the records specified in 59.407(b).
- Tonnage exemption under 59.404: the records specified in 59.407(c).
Separately, 59.408(b) requires each manufacturer and importer of a covered architectural coating to submit an initial notification report no later than the applicable compliance date specified in 59.400, or within 180 days after the first architectural coating is manufactured or imported, whichever is later. This initial notification is not conditional on using one of the three recordkeeping routes.
- Include the manufacturer's or importer's name and mailing address.
- Include the street address of each US facility producing, packaging or repackaging a covered architectural coating.
- Include the Table 1 categories for which the manufacturer's or importer's coatings meet the definitions in 59.401.
If a manufacture-date code is used, 59.408(b)(4) requires an explanation of each code in the initial notification report. An explanation of any new date code must be submitted no later than 30 days after its first use on a coating container.
05Fictional Practice Example: Label and Evidence Decision
The fictional figures below use the same basis: thinned to the maximum recommendation, excluding water and exempt compounds, without colorant added after manufacture. Difference means VOC content minus applicable limit. For each product, a qualified person reviews the label/lid proof's manufacture date or code, thinning recommendation and chosen VOC statement; supporting category and VOC-basis evidence; any date-code explanation; and route records if applicable. This review file is a practice recommendation, not a universal 59.407 duty.
Fictional Products A, B and C; the category limits are the federal Table 1 values above.
| Product and representation | Table 1 category | Applicable limit (g/L) | VOC content (g/L) | Difference (g/L) | Label/record evidence reviewed |
|---|---|---|---|---|---|
| Product A — Interior flat wall coating sold as a tint base; literature represents it only as flat. | Flat coatings — interior | 250 | 230 | -20 | Reconcile VOC-basis documentation with tint-base colorant treatment; review flat-only literature and the proof's selected VOC statement. |
| Product B — Interior semi-gloss represented only as nonflat. | Nonflat coatings — interior | 380 | 395 | +15 | Compare nonflat-only representations and VOC-basis documentation with the proof; flag any statement presenting 380 g/L as a limit the coating meets. |
| Product C — Ordinary interior primer (not represented or formulated as quick-dry) also specifically represented in its technical data sheet as a flat finish coat; no 59.402(c) exception applies. | Most restrictive of Primers and undercoaters (350 g/L) and Flat coatings — interior (250 g/L) | 250 | 300 | +50 | Read the technical data sheet alongside the container proof; the flat-finish representation prevents relying only on the primer category’s 350 g/L limit. |
Product A is 20 g/L below its selected limit, but that comparison alone does not establish satisfaction of every subpart requirement. Products B and C exceed their applicable limits by 15 g/L and 50 g/L respectively. For each, the documented next decision belongs to a qualified person: reformulate, hold, or evaluate a 59.403/59.404 route under its own conditions. A printed limit does not resolve either exceedance.
Frequently asked questions
Q.Can a label use lb/gal even though compliance is judged in g/L?+
Yes. Section 59.405(a)(3) allows either labeling unit. Section 59.402(a) and Table 1 note a nevertheless make metric units controlling for compliance; Table 1's English-unit values are informational.
Q.Does calling a coating a primer settle its category?+
No. Subject to 59.402(c), representations indicating multiple Table 1 categories trigger the most restrictive limit, including representations in technical literature. In practice, Review the container and associated literature together rather than treating the product name as the entire category decision.
Primary sources
- 40 CFR 59.400 — Applicability (eCFR, version as of 29 October 2026)
- 40 CFR 59.401 — Definitions: architectural coating, importer, manufacturer, primer, quick-dry primer, VOC content (eCFR, version as of 29 October 2026)
- 40 CFR 59.402 — VOC content limits, including (b) and (c)(13) (eCFR, version as of 29 October 2026)
- 40 CFR 59.405 — Container labeling requirements (eCFR, version as of 29 October 2026)
- 40 CFR 59.406 — Compliance provisions (eCFR, version as of 29 October 2026)
- 40 CFR 59.407 — Recordkeeping requirements (eCFR, version as of 29 October 2026)
- 40 CFR 59.408 — Reporting requirements (eCFR, version as of 29 October 2026)
- Table 1 to Subpart D of Part 59 — VOC content limits, including the Quick-dry coatings group and note a (eCFR, version as of 29 October 2026)
Further reading
Want to see how VOC Content (Architectural Coatings) could fit into your own records and workflows? Explore the related V5 pages or talk to our team about what applies to your operation.
