Foreign Material Control
A foreign material control program combines prevention, detection, rejection, investigation and learning to reduce physical contamination in manufactured products. Controls should follow the hazard, product and process; no single detector can find every material in every pack.

On this page · 16 sections
- 1What counts as foreign material
- 2Prevent contamination at source
- 3Choose detection for the actual hazard
- 4Control rejected product and tests
- 5Investigate and learn
- 6Inside V5: traceability around an event
- 7Explain it for your operation
- 8Start with a process-specific hazard analysis
- 9Establish detector performance honestly
- 10Define the affected product window
- 11Use finds and complaints as learning evidence
- 12A practical foreign-material event
- 13A proportionate implementation plan
- 14Internal review questions
- 15Records and evidence to retain
- 16Questions to ask when evaluating software
How does Foreign Material Control apply to your shop floor?
Pick your industry and scale — Ask V5 rewrites the definition in your context, gives a worked example, and shows what V5 does on day one.
01What counts as foreign material
Foreign material can include metal, glass, brittle plastic, stone, wood, rubber, bone or other unintended physical matter. Whether it is a hazard depends on size, shape, hardness, product, consumer and intended use.
The programme should distinguish hazardous foreign material, quality defects and expected natural material while preserving a route to investigate each complaint or detection.
02Prevent contamination at source
Use supplier specifications and controls, protected receiving and storage, equipment inspection, preventive maintenance, tool and parts accountability, glass and brittle-plastic controls, personnel practices, line clearance and controlled rework.
Assess breakage and maintenance before restarting. Account for fragments and evaluate affected product rather than relying only on a final detector.
03Choose detection for the actual hazard
Screens, sieves, magnets, filters, metal detectors, X-ray systems, optical inspection and manual examination have different strengths. Product effect, pack material, orientation, density, speed and contaminant size influence performance.
Validation or challenge work should represent the product, pack, line and intended contaminant. Routine checks confirm the device continues to operate as established.
04Control rejected product and tests
A detection system needs a reliable reject mechanism, secure reject collection, challenge frequency and response to failure. Record test pieces, result, time, line status and product window.
When a check fails, identify potentially affected production, place it under appropriate control and follow the approved assessment. Do not simply retest until a pass appears.
05Investigate and learn
Preserve the material safely, document where it was found, identify composition where useful, compare equipment and supplier sources, and trace the production window. Look for prior similar events.
Corrective action should address the source and control weakness. Trending complaints without denominator or consistent categories can hide recurrence.
06Inside V5: traceability around an event
V5 can connect material lots, production records, equipment, quality records, corrective actions and shipments. That context supports a faster human-led trace of the affected window and related lots.
V5 does not identify a contaminant from an image, validate detection sensitivity or autonomously decide release. Specialists and authorised quality personnel make those decisions.
07Explain it for your operation
Map credible foreign-material sources from receiving to dispatch, then list the preventive and detection control for each. Verify detector challenges, reject security and the response to a failed check during a real shift.
Select one recent find or complaint and trace it backwards. Record where evidence runs out and use that gap to prioritise improvement.
08Start with a process-specific hazard analysis
Identify credible materials, sources, points of introduction, consumer consequence and existing preventive controls. Consider raw materials, equipment wear, maintenance, packaging and people.
Document why each hazard is controlled by prevention, detection or both. Reassess after product, supplier, pack or equipment change.
09Establish detector performance honestly
Test pieces and challenge positions should represent the established capability for the product and pack. Product effect, aperture, speed, orientation and environmental conditions can alter sensitivity.
Record the validated or qualified setup and routine check method. Do not advertise the smallest theoretical contaminant as a universal detection guarantee.
10Define the affected product window
When a detector or reject check fails, determine the last known acceptable check, production since then, line stops, rework and product movement. Physically and electronically control the window while assessment occurs.
Reinspection or re-screening needs an approved, capable method and complete reconciliation. Retain the original event and decision.
11Use finds and complaints as learning evidence
Preserve contaminant, packaging and purchase or production details where possible. Laboratory identification may distinguish equipment alloy, mineral, bone or packaging source.
Trend consistent categories with distribution denominators, but investigate high-severity events individually. Link corrective action to a confirmed or evidence-supported source and check effectiveness.
12A practical foreign-material event
A metal detector challenge fails after a defined period of production. The team controls product since the last satisfactory check, records line and reject status, investigates the device and determines a justified reinspection route. It does not simply repeat the challenge until it passes.
If a fragment is found, composition and shape may be compared with equipment and raw-material sources. Traceability identifies affected lots and shipments, while quality personnel assess disposition. Corrective action addresses the source and the failed control, then verifies both.
13A proportionate implementation plan
- Confirm the applicable requirement, product scope and decision owner.
- Map the current method and the records already available.
- Define terms, responsibilities, evidence and exception handling in the approved procedure.
- Pilot the method on one representative process and challenge a difficult exception.
- Train affected roles, approve the change and monitor whether the method works as intended.
- Review after significant change and retain a transparent history of decisions.
Scale the formality to risk and complexity. A small operation still needs clear responsibilities and reconstructable evidence, while a multi-site operation also needs harmonised definitions, governance and comparison rules.
14Internal review questions
- Can a reviewer identify the source, owner, method and current approved version?
- Do summaries reconcile to original records and include unfavourable or missing evidence?
- Are exceptions visible, assessed and linked to the affected material, product or process?
- Are actions assigned, overdue items escalated and effectiveness reviewed?
- Have changes in product, supplier, equipment, method or regulation triggered reassessment?
- Does the record distinguish system support from the decision an authorised person made?
15Records and evidence to retain
- Approved scope, definitions and responsibilities for foreign material control.
- Source records and identifiers that let a reviewer reconstruct the work.
- Methods, assumptions, calculations, exclusions and any data-quality limitations.
- Exceptions, investigations, decisions, approvals and resulting actions.
- Version history showing when the approach changed and why.
Records should be proportionate to the decision and usable by someone who was not present. Preserve original evidence and corrections rather than replacing it with an unexplained summary.
16Questions to ask when evaluating software
- Can users trace every summary value back to its source record and version?
- How are roles, permissions, signatures and corrections recorded?
- Can the workflow reflect our approved procedure without inventing a universal rule?
- What happens during an outage, and how are later entries distinguished?
- Can we test the highest-risk exception with realistic data before committing?
- Which decisions remain explicitly assigned to an authorised person?
Frequently asked questions
Q.What is foreign material control?+
A foreign material control program combines prevention, detection, rejection, investigation and learning to reduce physical contamination in manufactured products. Controls should follow the hazard, product and process; no single detector can find every material in every pack.
Q.Is foreign material control required in every operation?+
The applicable product rules, market, risk and approved quality system determine what is required. The method should be justified for the operation rather than copied without context.
Q.Can software make the final quality decision?+
No. Software can organise records, calculations and workflow, but authorised people remain responsible for scientific, quality and disposition decisions.
Q.How should a site start?+
Choose one bounded process, define the decision and evidence, test the method with real records, correct gaps, then expand under change control.
Q.What evidence should be retained?+
Keep the approved method, source records, assumptions, exceptions, review, decision, approval and any resulting action with enough context to reconstruct the work.
Q.How often should it be reviewed?+
Use the applicable requirement and a risk-based cycle, with earlier review after significant change, failure, complaint, deviation or new knowledge.
Primary sources
Want to see how Foreign Material Control could fit into your own records and workflows? Explore the related V5 pages or talk to our team about what applies to your operation.
